Instructions.
** Cut the 94" of Beading Wire down further into (2) 20" lengths,
(1) 19" length, (1) 18" length, and (1) 17" length**
1) Take one SB805 and open two JR605 with PL490 and PL491. Attach the "hook"
half of CL005 to one of the open JR605, closing the jump ring after doing so.
Take this closed JR605 and attach this to the other open JR605. Before closing
this last jump ring, attach to the single loop on the back of SB805.
2) Make a chain out of the remaining JR605 by opening and attaching to one another.
Before closing the last JR605 on this chain, attach to the single loop on the
remaining SB805.
3) Take one of the 20" lengths of BW215 and thread on one BD315. Hold either
one of the SB805 in your non-dominant hand with the single loop side facing
toward your palm. This length of BW215 will be going through the bottommost
loop on the three-loop side. Take the wire around and back through BD315. Pull
the wire so that the crimp tube is fairly snug against the loop and crimp with
PL125. Cut any excess wire off with PL125.
4) Thread on eight BD845.
5) Thread on one BD255, one TQ020, another BD255 and two more BD845. Repeat
this step five more times.
6) Thread on one BD255, one TQ020, another BD255 and eight BD845. Thread on
another BD315. With the other SB805 in your non-dominant hand, thread the end
of this wire through the bottommost hole on the three holed side. Pull the wire
around and back through BD315 and pull until the crimp tube is fairly snug against
the loop. Crimp with PL125.
7) Take the other 20" length of BW215 and thread on another BD315. Take
the end of this wire through the same bottom loop on SB805 as used before. Take
the wire around and back through the BD315. Pull the wire until BD315 is snug
against the loop and crimp. Thread on seven BD845.
8) Thread on one BD255, one TQ020, another BD255 and two more BD845. Repeat
this step six more times.
9) Thread one one BD255, one TQ020, another BD255 and seven BD845. Thread on another
BD315. Thread this wire end through the same loop as the previous strand and
take the wire around and back through the BD315. Crimp after pulling the tube
snug against the loop.
10) Take the 19" length of BW215 and thread on one BD315. Thread this through
the middle loop, then back around and through the BD315. Pull snug and crimp
as before. Thread on six BD845.
11) Thread on one BD255, one TQ020, another BD255 and two more BD845. Repeat
this step six more times.
12) Thread one one BD255, one TQ020, another BD255 and five BD845. Thread on
another BD315. Take the end of this wire through the middle loop on the other
end of the necklace. Take the wire around and back through BD315. Pull snug
and crimp.
13) Take the 18" length of BW215 and thread on another BD315. Take the
end of this wire through the middle loop on SB805. Go around and back through
BD315 with the wire end and pull snug and crimp. Thread on five BD845.
14) Thread on one BD255, one TQ020, another BD255 and two more BD845. Repeat
this step six more times.
15) Thread one one BD255, one TQ020, another BD255 and six BD845. Thread on
another BD315. Take the end of this wire through the middle loop on the other
end of the necklace. Take the wire around and back through BD315. Pull snug
and crimp.
16) Take the last 17" length of BW215 and thread on the second to last
BD315. Thread the end of this wire through the uppermost loop on either one
of the SB805. Take the wire around and back through BD315. Pull snug and crimp.
Thread on four BD845.
To Finish.
17) Thread on one BD255, one TQ020, another BD255 and two more BD845. Repeat
this step five more times.
18) Thread one one BD255, one TQ020, another BD255 and the last four BD845.
Thread on the last BD315. Take the end of this wire through the uppermost loop
on the other end of the necklace. Take the wire around and back through BD315.
Pull snug and crimp.
